Standing Seam

Standing Seam is Professional looking low profile Metal Roofing.

 

*Click link to jump to panel.

1) Nail Strip

2) Snap Lock

3) Mechanical Lock

4) Batton

*Click image to view panel conditions
Flat Panel
metal building
Striations
metal building
Perforated
metal building
Pencil Ribs
metal building
metal buildingmetal buildingmetal buildingmetal buildingmetal buildingmetal building

 

Nail Strip


View Available Trim

Gauge Finishes Description
26
24
Painted Syliconized Polyester
Painted Kynar 500
Galvalume Az55
Comes in 1” or 1 1/2”. Custom widths are available upon request. Choose from multiple panel conditions such as, striations, ribbed, or flat pan.

 

Snap Lock

View Available Trim

Gauge Finishes Description
26
24
Painted Syliconized Polyester
Painted Kynar 500
Galvalume Az55
Cold Roll
Comes in 1” or 1 1/2”. Custom widths are available upon request. Choose from multiple panel conditions such as, striations, ribbed, or flat pan.

 

Mechanical Lock


View Available Trim

Gauge Finishes Description
26
24
Painted Syliconized Polyester
Painted Kynar 500
Galvalume Az55
Available in 1” or 1 1/2”. Choose from multiple panel conditions such as striations, ribbed, or flat pan.
*Custom widths are available on request.

 

Batten Panel

View Available Trim
Gauge Finishes Description
26
24
Painted Syliconized Polyester
Galvalume Az55
Painted Kynar 500
Cold Roll
Standing seam panel with 1″ rib height. Batton can be curved to fit multiple applications. Custom widths are available upon request. Choose from multiple panel conditions such as, striations, ribbed, or flat pan.
*Conditions only available on non-curved panels.

 

Trim Length Girth Gauge Description
standing seam
Ridge

10′-21′

13 6/8″

26
24

Used to cap the intersections of a standing seam roof at the peak. Can be used for gable or hip roofs.
transition
Hip

10′-21′

10″

26
24

Used at hip connections of a standing seam roof when something smaller than a ridge cap is desired as in smaller structures.
transition
Valley

10′-21′

20″

26
24

Used to flash valley connection.The valley lip helps to divert water if it reaches the top of the valley.
transition
W Valley

10′-21′

20″

26
24

Used to flash valley connections. The center rib helps slow the velocity of water entering the valley.
transition
W Valley w/wings

10′-21′

20″

26
24

Gives maximum protection in a valley of a roof. The center ridge slows down the velocity of the water while the upper wing keeps water from getting past the top of the valley.
transition
Zee Closure

10′-21′

N/A

26
24

Zees are used in conjunction with ridge, hip, rake, end wall, side wall, and high side trims to give them something to fasten to on top of the panel.
transition
Cleat

10′-21′

4″

26
24

This cleat is used to hold valleys in place under the panels.
transition
Starter Trim

10′-21′

4 1/2″

26
24

Can be used at the bottom of the panel to secure the panel to the decking.
transition
Offset Plate

10′-21′

3 1/2″

26
24

When an extended eave is not used at the eave this can be used to fasten to the decking and hem the panel to.
transition
Perimeter Cleat

10′-21′

2″

26
24

This is used in conjunction with rake, eave, high side, and parapet caps to prevent the use of through fastened screws.
transition
Eave

10′-21′

8 1/8″

26
24

Used at the eave of the building to flash the fascia and to help protect against water that comes from the end of the panel.
transition
Rake

10′-21′

9 1/2″

26
24

Installed at the gable end of a structure to help hold down the panel as well as prevent water from blowing under the roof panels at the gable end.
transition
Endwall

10′-21′

10″

26
24

Flashes the area between the wall and the panel where the panel runs perpendicular to the wall. Please specify the pitch.
transition
Sidewall

10′-21′

10″

26
24

Flashes the area between the wall and the panel where the panel horizontal to the wall.
transition
Transition

10′-21′

12″

26
24

Used where two roofs meet to flash the changes in pitch such as a where a porch connects to a main roof.
transition
Extended Eave

10′-21′

8″

26
24

Used at the eave of the structure and features a projection for panel support as well as something to hem the panel to.
transition
High Side Trim

10′-21′

10″

26
24

Used at the top of a shed type roof to keep water from blowing in underneath the panels.
transition
Fascia Trim

10′-21′

N/A

26
24

Used to apply to the fascia board for cosmetic reasons as well as to protect against water.
Batton 1
Batten (Medallion 1)

n/a

n/a

n/a

For use with the Standing seam panel “Medallion 1”.
Batton 2
Batten (Medallion 2)

n/a

n/a

n/a

For use with the STanding Seam panel “Medallion 2”.
Batton 1
Wide Batton Clip

n/a

n/a

n/a

For use with the Batton Standing Seam Panel.
Batton 1
1″ Snap Lock

n/a

n/a

n/a

For use with the 1″ snap lock Standing seam panel.
Clip Specifications
Batton 1
1 1/2″ Snap Lock

n/a

n/a

n/a

For use with the 1 1/2″ snap lock Standing Seam panel.
Clip Specification
Batton 1
1″ Butterfly Clip

n/a

n/a

n/a

For use with the 1″ Batton Stading Seam panel Clip Specifications
Batton 1
1 1/2″ Butterfly Clip

n/a

n/a

n/a

For use with the 1 1/2″ Batton Standing Seam panel.